Cyclo Fabrica
Cyclo Fabrica
Opening hours
- Sunday
- Closed
- Monday
- 10 AM - 6 PM
- Tuesday
- 10 AM - 6 PM
- Wednesday
- 10 AM - 6 PM
- Thursday
- 10 AM - 6 PM
- Friday
- 10 AM - 6 PM
- Saturday
- Closed
146 Gloucester Road, Bishopston
Bristol BS7 8NT
Bristol BS7 8NT
Services
A full strip down rebuild of your bike. All parts removed and cleaned, all bearings removed and re-greased. Headset, Bottom Bracket, and Hubs serviced. Gears adjusted and aligned. New cables, pads fitted as required. Will come back better than new! (parts extra)
A comprehensive check over of your bike including, gear and brake adjustment and alignment, wheels trued, headset, Bottom Bracket and hubs checked and adjusted, and drivechain lubricated. New parts fitted at extra cost.
Full custom bike build from parts. Includes any preparation if required for resprayed frames such as facing, thread chasing and fork steerer cut.
Full build of any boxed bike bought online.
Service, adjustment and alignment of front and rear derailleurs mechanical or electronic. New cables fitted if required.
Brake adjustment and alignment for a pair of rim or disc brakes. Cables, pads or blocks checked for wear and replaced if required. (Parts extra)
Servicing or fitting of a Bottom Bracket. New grease, threads checked, bearings replaced if required. (Parts extra)
Fitting or service of a headset, new grease, bearing check or replacement, pressing in of cups, as required. (Parts extra)
All pedal types serviced, Shimano, Speed Play, Look, etc. Includes full strip down and rebuild with fresh grease and bearing adjustment. (Parts extra)
Full bleed of a single brake. Includes brake fluid (mineral or dot) rotor and pad check.
Full bleed of a pair of brakes. Includes brake fluid (mineral or dot) rotor and pad check.
Fitting of supplied bar tape. FOC if purchased in store.
Fitting of mudguards from £25. Optional fitting of rear dynamo lights, custom bracket fabrication, mudguard rivit repairs available.
Free warranty inspection of affected Shimano ULTEGRA FC-6800, DURA-ACE FC-9000, ULTEGRA FC-R8000, DURA-ACE FC-R9100 and FC-R9100-P 11-Speed Bonded HOLLOWTECH II Road Cranksets
For insurance or costing for your bike after a crash or accident.
Hand built wheel including spoke length calculation.
Tension and true of wheel, spoke replacement as required. Spokes charged extra.
Strip down & service of hub with fresh grease. Parts cleaned and checked, new bearings fitted if required.
Strip down and rebuild of your freehub. Pawls, ratchet system cleaned and re-assembled with correct lubrication for the hub type. Bearings re-greased or replaced. (Parts extra)
Sealant, Tyre, Tape and Valve check/fit as required for a single wheel. (Parts extra)
Sealant, Tyre, Tape and Valve check/fit as required for a pair of wheels. (Parts extra)
Repair or replace tube and refit. Includes high quality Rema patch and glue. Optional replacment tube at extra cost.
Facing of disc mounts for IS, Post, and Flat mount.
Milling and facing of a fork crown. Includes fitting of lower headset race.
Reaming and facing of the headtube to allow precise fitting of headset cups.
Tapping and chasing of threads in a newly painted frame or a frame with a damaged or rusted Bottom Bracket.
Tapping and cleaning of any damaged or painted threads on a bike. For bottle cage bosses, derailleur hangers, seatbolts and more. All thread types and sizes possible.
Facing and milling of frame to allow precise fitting of new Bottom Bracket
Reaming of freshly painted or damaged, rusted seatpost to take it back to correct diameter for seat post fitting.
For Alloy or Carbon frames where a bottle cage bolt has become loose or a stuck bolt. Includes removal/drilling out of old boss and bolt and fitting of a new rivnut.
For small areas of corrosion on your frame. Includes sanding and prepare frame, masking of surrounding areas and respray. Paint included, mainly for rust or corrosion issues on steel or aluminium frames. Full resprays are also available, contact for details.
For any seized bolts on your bike. Normally bottle cage or mudguard bolts but also hydraulic caliper pins or anything else you cant get out! Includes drilling out, re-tapping of threads and new bolt.
From £55... call for details. Cost dependent on kit type, generic, frame only, frame & fork. And new bike/frame or used bike/frame.
Removal of stuck seat pin or handlebar extension. From £45
Cutting down of a fork steerer on an existing bike or fitting a new fork. Includes fitting of star fangled nut or carbon steerer expanding bung. Threading of a steel fork available at extra cost.
Lowers removed and cleaned, oil replaced, forks tested. Strip, clean and relube of air/spring assembly. Seals checked and replaced if required. (Seal kit extra)
Removal and inspection of damper unit. Oil replacement, new seals if required. Lock out adjustment and set up.
Removal and refit of a pair of rear shock pivot bushes. (parts extra)
Full bleed and speed adjustment set up of a Rockshox Reverb Dropper post.
Fitting of cable or hydraulic dropper post, internal or external type.
Removal and clean of all drivechain components, Front & rear mechs, chain, cassette, and chainset.
Ultrasonic cleaning of chains, cassettes, mechs, components as required. Includes removal and refit of parts.
Di2 Firmware update for all components, battery consumption check, Shimano service report.
Rebuild of your Di2 battery with two replacment 650mAh cells with higher mAh. (Incudes batteries) firmware update and capacity test. Available for BT-DN110 and BT-DN110-A
Dynamo lighting set up, includes custom wiring and fitting of front and rear lights. Optional extras include USB Charging installation and custom bracket fabrication.
Repairs, servicing and diagnostics for Bosch, Shimano, Yamaha and other systems. From £35
Good to know
Gallery
Reviews
, Highest rated
- Paul Goodman··from Google
Paul did a great service on my bike and sorted a sheared bolt for me. Booking process was straightforward. The bike feels great.
- David Townsend··from Google
Paul is great. Attentive, competent and lovely to deal with. Highly recommend.
- Chris Marsden··from Google
Took my bike in to activate the light setting on my emtb with Bosch motor. He was very friendly and informative and in the 10-15 minutes I chatted with him he gave me lots of advice. Sorted my problem in around 30 minutes and as soon as he was done sent me photos of my light working and screenshots of the diagnostics. Will most certainly be taking my bike here again for servicing or if there are any other issues. Very professional and would highly recommend
- Dawid W··from Google
Fantastic service quick and reliable! Definitely recommended for a fix and a great chat! Thanks a lot!
- Martin Fraser··from Google
Excellent service from Cyclo Fabrica. Bike stripped down, cleaned, regreased and returned in very good order. Superb service as ever, thanks.
- Christian Milton··from Google
He couldn't be nicer or more helpful with advice
Opening hours
- Sunday
- Closed
- Monday
- 10 AM - 6 PM
- Tuesday
- 10 AM - 6 PM
- Wednesday
- 10 AM - 6 PM
- Thursday
- 10 AM - 6 PM
- Friday
- 10 AM - 6 PM
- Saturday
- Closed